Rev-A-ShelfDouble Pullout Trash Can for Base Kitchen/Bathroom Cabinets, 35 Qt Wood Top Mount Garbage Bin, 21" x 1.5" Face-Frame, White, 4WCTM-24DM2

This is a great solution for retrofitting a recycle bin into dated kitchen cabinetry. I'd been leaving a bin on the floor for recycling and it was super annoying. My trash was always on a hideaway roller (came with the house) but the space use was inefficient. This product fits perfectly into standard 15" opening cabinetry. The installation is fairly simple and the result is smooth and durable.I say the installation is simple. But the instructions are useless - and I'm being kind. I've installed other Rev-a-Shelf products with good explanations and even templates. This is a disappointing exception. I am pretty handy and simply figured out the solution by making lots of measurements and going old-school. But I warn those of you who might struggle with righty-tighty/lefty-loosey. Hire a handyman. And don't let him/her look at the instructions.Rev-a-Shelf: If you read these reviews-> Fix these instructions. And seriously reconsider the employment of the folks who wrote and approved them.

Many, many years ago, a contractor installed this into our kitchen. it worked great, but after many years, one of the ball bearings got jammed, and I was able to fix it with a plier easily. After looking at the unit, we decided based on visual wear and tear we wanted to replace it. I found the manufacturer and part number on the bottom of the basket and ordered the new one.Today we installed it, and it only took minutes because everything fit perfectly even after all these years. We only needed one screwdriver.I love that I have both my recyclable and garbage baskets in one drawer.

I ordered this for our kitchen redesign. Cabinets are solid wood face, and 18 years old, so irreplaceable if i messed up. I did need to add blocking to the back of my cabinet because it is a counter deep one. I also waited to attach my new cabinet pulls until trash can was installed to get the handle placement right. Extremely sturdy, great slides, and rolls well(once i edited my cabinet face.) I did measure, but my old cabinets where just two millimeters off on each side(just enough that it didn't slide in and out without scraping). I fixed this by using a Dremel tool and "sanding" the two sides at the face install location on each side, ONLY where the bar was screwed. Trial and error made it take about an hour to install. I really love it now that it is in. I recommend a solid door pull, centered on cabinet for ease of use, as it still has a bit of friction.my own critical is the back bag is hard to get out when full, as the unit doesn't pull completely out. But I still love it. And the plastic bin sizes are a good size for a family of five.

The produce is very well made. The sliders are high quality and slide out fully. The wood parts that hold the containers are very well put together with dovetail joints just as you see in the ad, a reasonable mix of plywood and solid wood, and lacquer finish. And it comes assembled so you don't have to puzzle about that. The instructions are understandable, with very nice diagrams. My only complaint was that they did not mention anything some of my particular setup. I'll describe that here:For reference, the first image is a before image. I had to remove a shelf, and note that my cabinet doors are inset: the edges are cut so that they are partly inside the cabinet, if that makes sense. All the descriptions and drawings in the documentation were for flat doors that apparently close flat against the front panel of the cabinet. This resulted in a 3/8" gap (see the 4th image showing the cabinet door after installing the unit. Once I realized the problem, I removed the front screw where the sliders attach to the front panel, and screwed them in 3/8" farther into the cabinet. There is a slide at the back end of each slider that allowed me to move it back. The problem for me was that I had to install a block to screw into because the front panel was not thick enough. You can see the block in the 5th picture, looking down from the top. Now I was able to make the front door fit perfectly.I was confused by the instructions about how to screw the sliders into the front panel. You can see in figure 2 that the slider does not look like the diagram (their Fig E in step 4). The diagram doesn't show the ball bearing slide which obscures the rectangular holes. It took me a while to realize that I could adjust that slide as shown in image 3 to allow me to screw it to the frame.A final confusion was that the instructions include 3 ways to measure and install the front cabinet door. There are 2 ways in the main instructions, and I also got a second set of instructions just for installing the door with yet a different way. It was all very complicated so it was easier for me to ignore all 3 methods and just work it out on my own.Given the complications I described, and having to redo some things because of them, it took me several hours to install it, not the 30-40 minutes they mentioned. But I don't mean to complain too much about that because probably most people have to adjust some things. It is a very solid construction and I'm very pleased with it.

Item was easy to install and fit perfectly in my 18" base cabinet. The productvisbvery sturdy and the cabinet door feels secure.

The product is wonderful. We did however receive the wrong size. We ordered a smaller unit that would have fit into our existing cabinet and were very discerning about the size. The code was different and it was the next size up. We were on a time-line and my husband is very handy so he renovated to fit it under our counter. It was challenging but worked out well in the end.

Great product very sturdy, instructions were poor takes some shimming of the side wall glides for everything to align

had modify opening of cupboard to fit unit

Works great. Way better than the one that gets installed on the bottom of the cabinet. It's strong and holds the weight well.

j'adore !